All items listed are located in-house at our primary facility in Pennsylvania.

Page: 1 of 66
Air Conveyor Section

-(Line 8)
-Adjustable Height
-Infeed to crown 60 valve filler
-Touch screen control for crown filler mounted on frame
-90ft conveyor
-Ling Systems conveyors
Stock#: 13243
In Stock
Amonia Tank for Carbo Cooler

-(Line 1)\
-Works with 13231
Stock#: 13245
In Stock
3M Top & Bottom taper

- Manually adjusted top & bottom taper
- Casters.
- 2 inch tape heads.
- 120 Volts
Stock#: 12321
In Stock
45" D Rotary feed Table

- All stainless steel
- DC voltage speed control
- 110 volts - 60 Hz
- 32" wide x 23" deep loading tray
Stock#: 12714
In Stock
60 Gal. Stainless Steel Jacketed Kettle

- 45 PSI
- Jacket on half of product contact surfaces
- Center bottom outlet
- 33" Diameter x 22" Deep
Stock#: 13137
In Stock
98" L x 20" W Conveyor Stainless Steel

- Adjustable height 24"- 40"
- .5 HP Motor with Gearbox ratio of 30:1
- 240/480 V
- Valu-Guide Sides
- Table Top Chain Conveyor 3-1/4" W.
Stock#: 13106
In Stock
Abbe 6 Gallon Vacuum Blender

- 6 gallon jacketed vacuum rated unit with heat and vacuum instrumentation.
- Twin agitation and side bottom outlet.
- Vertical pneumatic lid lift assembly.
- Two sanitary inspection-sample ports.
- 115 / 208-230 volts.
- Unit on casters
Stock#: 12247
In Stock
Accumulation Rotary Table

- 48" Stainless steel rotary turntable
- 20" x 18" tray table.
- 90VDC variable speed drive
- 120V single phase.
Stock#: 12477
In Stock
Accumulation Rotary Table

- Stainless steel construction
- 30" rotary table
- DC drive
- 120 volt single phase
Stock#: 12756
In Stock
Accumulation Rotary Table

- Stainless steel construction
- 30" rotary table
- DC drive
- 120 volt single phase
Stock#: 12759
In Stock
Accumulation Table

-Allen Bradley Start/Stop Switch
-Reliance Tigear Speed Reducer: Input R.P.M.: 1750

-Length: 39in
-Width: 39in
-Height: 38in
-Diameter: 36in

Baldor Motor:
-CAT NO: VM3538
-SPEC: 34A63-872
-Hp: 0.5
-Volts: 230/460
-Amps: 2/1
-R.P.M: 1725
-Frame: 56c
-Hz: 60
Stock#: 13287
In Stock
Aidlin Cap Sorter Elevator

- Highly efficient cap orientation on a small footprint.. Aidlin patented 3 in one Cap Feeder orientates based on the geometry of the closures. Parts are gently lifted up from the bulk hopper. Properly orientated caps continue traveling vertically to the discharge chute and the discriminated parts return to the bulk hopper for recycling. The properly orientated closures are then conveyed to the capper through either a chute or an Aidlin Cap Conveyor.
- Orients plastic or metal closures 20mm. to 120mm
- Maximum speed up to 3 000 cpm
- Orient Push-Pull Sports caps at rates up to 650 cpm
- Quick change-over with patented "Speed bump"
- All stainless steel wash-down construction
- Variable speed control
- Clean-out door to ensure all caps are out of hopper for quick changeover
- 20 cubic feet bulk hopper
- Left or right hand dischargeOptions
- Clear Lexan dust cover on hopper for sanitation
- Anti-static belt for metal closures
- Low level sensor and signal for hopper replenishment
- 40 cubic feet bulk hopper
- Dual discharge outlet chute
- Dual "T" cleat to accommodate both beverage and sports caps
- Large capacity hopper reduces materials handling and labor requirement for replenishment of the feeder
- Parts replenishment is done at a safe floor level.
- Gentle handling of caps suitable for fragile tamper-evident rings or thin walled closures
- Low maintenance
- Suitable for placement remotely from the capper thus conserving floorspace and reducing traffic
- Quick changeover to accommodate different size closures. Aidlin Cap Feeder can be connected to Flat Top Air Trans conveyor to allow any remote location of the equipment
- From a standard basic modular design the Aidlin Cap Feeder is adaptable to suit your plant layout and production requirements
- Last running 43 mm caps

(9020 KHS MonoBlock
Stock#: 12475
In Stock
Page: 1 of 66
Berks Plant Design & Maintenance 150 Birch Hill Road Shoemakersville, PA 19555 Phone: 610-916-0666 Fax: 610-926-1584 Email:
Berks Plant Design & Maintenance's headquarters is located in Berks County in Shoemakersville, PA. We provide packaging equipment, process machinery, bottling equipment, parts, and services to clients anywhere in the United States, Canada, Mexico, and other points abroad. Our clients know our reputation for our expertise and excellence in customer service. Our equipment experts will help you identify your needs, and work with your budget to get you the best possible equipment solutions for your next project.